使用shell腳本計算Linux網卡流量，方法中最關鍵點：
復制代碼 代碼如下:
ifconfig $eth_name | grep bytes | awk '{print $6}' | awk -F : '{print $2}'
通過ifconfig eth0|grep bytes 得到輸入輸出的流量。
復制代碼 代碼如下:
/@rac2=>dd2$ifconfig eth0|grep bytes
RX bytes:1638005313300 (1.4 TiB) TX bytes:3408060482049 (3.0 TiB)
再將結果通過awk 得出所要的字段值。
固定時間得到這些值，在寫個循環(huán)計算一下就能得到網卡流量。
完整代碼：
代碼一：
#!/bin/bash
# 統(tǒng)計網卡流量
# link：www.jb51.net
# date：2013/2/26
n=10
date
rm -rf /tmp/ifconfig_log
while (( $n >= 0 ))
do
n=$(($n - 1));
date >> /tmp/ifconfig_log
ifconfig eth1 >> /tmp/ifconfig_log
sleep 1
done
grep "RX bytes:" /tmp/ifconfig_log | awk -F"[:| ]" '{print $13}' | awk 'BEGIN{tmp=$1}{if(FNR > 1)print $1-tmp}{tmp=$1}'
代碼二：
#!/bin/bash
if [ -n "$1" ]; then
eth_name=$1
else
eth_name="eth0"
fi
i=0
send_o=`ifconfig $eth_name | grep bytes | awk '{print $6}' | awk -F : '{print $2}'`
recv_o=`ifconfig $eth_name | grep bytes | awk '{print $2}' | awk -F : '{print $2}'`
send_n=$send_o
recv_n=$recv_o
while [ $i -le 100000 ]; do
send_l=$send_n
recv_l=$recv_n
sleep 1
send_n=`ifconfig $eth_name | grep bytes | awk '{print $6}' | awk -F : '{print $2}'`
recv_n=`ifconfig $eth_name | grep bytes | awk '{print $2}' | awk -F : '{print $2}'`
i=`expr $i + 1`
send_r=`expr $send_n - $send_l`
recv_r=`expr $recv_n - $recv_l`
total_r=`expr $send_r + $recv_r`
send_ra=`expr \( $send_n - $send_o \) / $i`
recv_ra=`expr \( $recv_n - $recv_o \) / $i`
total_ra=`expr $send_ra + $recv_ra`
sendn=`ifconfig $eth_name | grep bytes | awk -F \( '{print $3}' | awk -F \) '{print $1}'`
recvn=`ifconfig $eth_name | grep bytes | awk -F \( '{print $2}' | awk -F \) '{print $1}'`
clear
echo "=================================================="
echo "Last second : Send rate: $send_r Bytes/sec Recv rate: $recv_r Bytes/sec Total rate: $total_r Bytes/sec"
echo "Average value: Send rate: $send_ra Bytes/sec Recv rate: $recv_ra Bytes/sec Total rate: $total_ra Bytes/sec"
echo "Total traffic after startup: Send traffic: $sendn Recv traffic: $recvn"
echo "=================================================="
done
代碼三：
#!/bin/bash
# Link: www.51bbo.com
###
while :
do
Time=`date +%F” “%T.%N`
rx_before=`ifconfig eth0 |sed -n 8p |awk ‘{print $2}'| cut -c7-`
tx_before=`ifconfig eth0 |sed -n 8p |awk ‘{print $6}'| cut -c7-`
sleep 2
rx_after=`ifconfig eth0 |sed -n 8p |awk ‘{print $2}'| cut -c7-`
tx_after=`ifconfig eth0 |sed -n 8p |awk ‘{print $6}'| cut -c7-`
rx_result=$[(rx_after – rx_before)/512]
tx_result=$[(tx_after – tx_before)/512]
echo -e “$Time nNow_In_Speed: ‘$rx_result'Kbps Now_OUt_Speed: ‘$tx_result'Kbpsn”
done
您可能感興趣的文章:- MyBatis異常-Property ''configLocation'' not specified, using default MyBatis Configuration
- Linux CentOS 6.5 ifconfig查詢不到ip的解決方法
